| AISI 1017 Steel, cold drawn | |
|---|---|
| Categories: | MetalFerrous MetalCarbon SteelAISI 1000 Series SteelLow Carbon Steel |
| Material Notes: | Medium-low carbon steels have good weldability and slightly better machinability than the lower carbon steels. Relatively soft and strengthen with cold work during forming or drawing |
| Key Words: | AFNOR NF A35-556 XC18, AIR 9160-C21 9160C011, DIN 17210 1.1141, DIN 17210 Ck15, MSZ 500 B38 X (Hungary), AFNOR XC15, AFNOR NF A35-551 XC18, AFNOR NF A35-552 XC18, AFNOR NF A35-553 XC18S, AFNOR NF A35-554 XC18S, carbon steels, UNS G10170, ASTM A29 1017, ASTM A29 M1017, ASTM A510 1017, ASTM A513 1017, ASTM A519 1017, ASTM A575 M1017, ASTM A635 1017, ASTM A659 1017, ASTM A830 1017, MIL-S-11410 1017, MIL S-11410 CS1017, BDS 2592 BSt3kp (Bulgaria), BDS 2592 BSt3ps, BDS 2592 BSt3sp, BDS 9801 VSt3kp, BDS 9801 VSt3ps, BDS 9801 VSt3sp, BDS 9801 WSt3kp, BDS 9801 WSt3ps, BDS 9801 WSt3sp, GB 714 A3q (China), GB 900 B3, GB 900 B3F, GB 900 C3, GB 300 C3F, JIS S15C, JIS S15CK, JIS G4051 S17C, DGN B-301 1017 (Mexico), COPANT 333 1017, STAS 10607 16 (Romania), PN 84023 18A (Poland), PN 84023 St3NO, PN 84024 R45, PN 84024 R45A, PN 84024 St44K, SAE J1397 1017, SAE J403 1017, SAE J412 1017, ONORM M3110 RC15 (Australia), NBN 253-03 C16-2 (Belgium), AISI1017 |
| Vendors: | No vendors are listed for this material. Please click here if you are a supplier and would like information on how to add your listing to this material. |
 Printer friendly version Download to Excel (requires Excel and Windows)
Add to Folder: | |
Export data to your CAD/FEA program| Physical Properties | Metric | English | Comments |
|---|---|---|---|
| Density | 7.87 g/cc | 0.284 lb/in³ | |
| Mechanical Properties | Metric | English | Comments |
| Hardness, Brinell | 116 | 116 | |
| Hardness, Knoop | 135 | 135 | Converted from Brinell |
| Hardness, Rockwell B | 66 | 66 | Converted from Brinell |
| Hardness, Vickers | 120 | 120 | Converted from Brinell |
| Tensile Strength, Ultimate | 405 MPa | 58700 psi | |
| Tensile Strength, Yield | 340 MPa | 49300 psi | |
| Elongation at Break | 18 % | 18 % | In 50 mm |
| Reduction of Area | 40 % | 40 % | |
| Modulus of Elasticity | 205 GPa | 29700 ksi | Typical for steel |
| Bulk Modulus | 160 GPa | 23200 ksi | Typical for steel |
| Poissons Ratio | 0.29 | 0.29 | Typical For Steel |
| Machinability | 65 % | 65 % | Based on AISI 1212 steel = 100% |
| Shear Modulus | 80.0 GPa | 11600 ksi | Typical for steel |
| Electrical Properties | Metric | English | Comments |
| Electrical Resistivity | 0.0000159 ohm-cm @Temperature 0.000 °C | 0.0000159 ohm-cm @Temperature 32.0 °F | estimated by comparison with similar materials |
| Thermal Properties | Metric | English | Comments |
| Specific Heat Capacity | 0.481 J/g-°C @Temperature >=95.0 °C | 0.115 BTU/lb-°F @Temperature >=203 °F | condition unknown |
| Thermal Conductivity | 51.9 W/m-K | 360 BTU-in/hr-ft²-°F | estimated based on similar materials |
| Component Elements Properties | Metric | English | Comments |
| Carbon, C | 0.14 – 0.20 % | 0.14 – 0.20 % | |
| Iron, Fe | 99.11 – 99.56 % | 99.11 – 99.56 % | As remainder |
| Manganese, Mn | 0.30 – 0.60 % | 0.30 – 0.60 % | |
| Phosphorus, P | <= 0.040 % | <= 0.040 % | |
| Sulfur, S | <= 0.050 % | <= 0.050 % | |
References for this datasheet.
Some of the values displayed above may have been converted from their original units and/or rounded in order to
display the information in a consistent format. Users requiring more precise data for scientific or engineering
calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding
error. We also ask that you refer to MatWeb’s terms of use regarding this information.
display the information in a consistent format. Users requiring more precise data for scientific or engineering
calculations can click on the property value to see the original value as well as raw conversions to equivalent units.
We advise that you only use the original value or one of its raw conversions in your calculations to minimize rounding
error. We also ask that you refer to MatWeb’s terms of use regarding this information.
Click here to view
all the property values for this datasheet as they were originally entered into MatWeb.